Few more brews.
Flavored Nolvadex!!
This is my own brew, someone told me it wasnt staying in solution, however it has been fine for the last 6 weeks for me. If it starts to sperate just re-heat and shake.
Needed:
-4grams Nolvadex Powder
-94mls Peg-400
-2mls Flavor extract, IE Peppermint, Cinnimon, etc.
Weight the 4grams of powder into a 100ml vial, I like to use screw top vials for orals. Add the 94mls of PEG to the powder, and shake. Then add your 2mls of flavoring, and shake again. Heat in a pan until fully dissolved. Some filter after this step, but because its oral there is no need, your body will filter out anything the fell into there. You already breathed it in if its floating in the air anyways. This can be done without the flavoring and just use 96mls of PEG.
Testosterone 500mg/ml, 40mls!! (Yes Test 500)
Recipe to make a almost painless 40ml of 500mg/ml Testosterone product.
Tools needed:
1 - 10ml Syringe
1 - 20ml Syringe
2 18ga pins/ 1 25ga pin
1 - .45 Whatman Sterile Syringe Filter
12ml Oil
2ml BA
6ml BB
2 - 50ml Sterile Vials
Scale Accurate to .1g
10g Test Enanthate Powder
10g Test Cypionate Powder
Rubbing Alcohol and Kleenex/Paper Towels
First thing i did was take out my enanthate powder out of the freezer and put it in a glass jar (that i'd cleaned out with alcohol and put in oven to dry out). I put the lid on jar and melted the brick of enanthate till it was complete liquid. I then took out the 10ml syringe and weighed it out on my scale. Then sucked up 10ml of enanthate liquid/powder to see gram to CC ratio. It worked out to be 1.05g per ml of enanthate. The reason i did this is when using the powder calculator (sticky material at top of thread), you have to enter in powder weight and i for one don't trust the accuracy of the calculator unless i measure out myself the powder weight calculation.
I squirted 10g of enanthate into the vial :
Next, i put a small funnel into the vial and then put it onto the scale and zero'd it out. I then added 10g of cypionate powder. It took up 1ml per gram of powder displacement.
Pushed the powder in to the vial using a metal rod, and then added both the BA and BB
then added 8 of the 12 total CC's of oil to the vial. I also crimped the vial so when drawiing out liquid to filter the stopper doesn't come off. I've used duct tape before aswell, both work fine. Save the 4CC's of oil till the end of experiment as you will need it to purge the filter to get all remaining hormone out of filter.
Boil some water on the stove in a pot. Remove from heat and then shake/drop vial into water to help mix up all ingredients. The heating will also speed up the filtering process.
After around 10-15 minutes (or when everything is dissolved and in solution) you are ready to filter. Here it is with 4ml of leftover oil that's gonna be used later.
Take out the rubbing alcohol/kleenex and wipe the rubber stopper of the second sterile vial. Peirce both a 25ga and a 18ga needle through stopper, aswell as attach whatman filter to 18ga needle.
Using second 18ga needle, suck up 20ml of unfiltered mix and attach to filter. Push plunger down until all 20ml's are done then suck up remaining unfiltered solution and repeat.
Run remaining 4ml of oil that's left through the filter.
Final result, 40ml of golden 500mg/ml of long estered testosterone. Leave 25ga pin in and heat at 250 F for 45 minutes. (THIS WAS MY BUDDY KC's POST)
|